DEMO1 4.10a shots

ETS input shots • ETS predictive runs

Following simulations are available for DEMO1 machine in UAL 4.10a:

!!! DATA are based on the ITM test release and can not be used for the scientific publications about DEMO

The shots can be accessed from the private data bases of IMP3 contributors by selecting the TOKAMAKNAME = demo1 and the UAL version = 4.10a

There are two ways to copy the data to your local data base:
You can copy them directly from the data provider data base as it is mentioned in the table:

cp ~user/public/itmdb/itm_tree/demo1/4.10a/mdsplus/0/euitm_ShotRun.* $MDSPLUS_TREE_BASE_0/.

You can check out the data from svn:

svn co --force https://gforge6.eufus.eu/svn/keplerworkflows/trunk/4.10a/imp3/DATA/DEMO1 $(MDSPLUS_TREE_BASE_0)

ETS input shots

Top • Previous • Next

These are copies of shots, generated originaly with other codes or containing the experimental data, which were migrated to the ITM-Gateway machine with the tools like Exp2ITM
These are used to start the ETS run and, therefore, might not provide the comlete set of consistent data.

Shot	Run	CPOs	user	generated with	description
1	1	equilibrium coreprof	denka	configured manually	ETS input shot, peaked density profile [time: 0.0; composition: e,D,T; ip=16MA Bt=6.791T, ; plasma boundary is prescribed from earlier FBE simulations / very shaped cross-section - difficult for equilibrium solvers to work with]
1	2	equilibrium coreprof	denka	configured manually	ETS input shot,peaked density profile [time: 0.0; composition: e,D,T; ip=16MA Bt=6.791T, ; plasma boundary is defined analiticaly]
1	11	equilibrium coreprof	denka	configured manually	ETS input shot, peaked density profile [time: 0.0; composition: e,D,T; ip=16MA Bt=6.791T, ; slightly smoothed boundary compared to the run 1]
2	11	equilibrium coreprof	denka	configured manually	ETS input shot, flat density profile [time: 0.0; composition: e,D,T; ip=16MA Bt=6.791T, ; slightly smoothed boundary compared to the run 1]

ETS predictive runs

Top • Previous • Next

These are ETS simulations, in which some physics study was done.
Short description of the run configuration is available in the table below. Nonetheless, we strongly advise you to contact the run author for the details.

Shot	Run	CPOs	user	generated with	description
1	3	equilibrium coreprof coresource coretransp	denka	ETS/BGB/ETB/GAUSS	ETS predictive ad hoc run / peaked density profile / shaped boundary [time: 0.1-1.0; composition: e,D,T; ip=16MA Bt=6.791T, ; predictive equations: Jpar,Ti,Te; sources: GAUSS [10MW to el / 20MW to D /20 MW to T]; Transport: BGB+ETB(at 0.97); Impurity: OFF]
1	4	equilibrium coreprof coresource coretransp	denka	ETS/BGB/ETB/GAUSS	ETS predictive ad hoc run / peaked density profile / analytical boundary [time: 0.0-1.0; composition: e,D,T; ip=16MA Bt=6.791T, ; predictive equations: Jpar,Ti,Te; sources: GAUSS [10MW to el / 20MW to D /20 MW to T]; Transport: BGB+ETB(at 0.97); Impurity: OFF]
1	12	equilibrium coreprof coresource coretransp	denka	ETS/CHEASE/BGB/ETB/GAUSS	ETS predictive ad hoc run / peaked density profile / smoothed boundary [time: 0.0-1.0; composition: e,D,T; ip=16MA Bt=6.791T, ; predictive equations: Jpar,Ti,Te; sources: GAUSS [10MW to el / 20MW to D /20 MW to T]; Transport: BGB+ETB(at 0.97); Impurity: OFF]
1	13	equilibrium coreprof coresource coretransp	denka	ETS/CHEASE/BGB/ETB/GAUSS	ETS predictive run / peaked density profile / smoothed boundary [time: 0.0-1.0; composition: e,D,T,Ar,W; ip=16MA Bt=6.791T, ; predictive equations: Jpar,Ti,Te,nz; sources: GAUSS [26MW to el / 192MW to D / 192 MW to T]; Transport: BGB+ETB(at 0.97); Impurity: ON; radiation fraction: 50%; current drive: 35%; Zeff: 3.0]
2	12	equilibrium coreprof coresource coretransp	denka	ETS/CHEASE/BGB/ETB/GAUSS	ETS predictive run / flat density profile / smoothed boundary [time: 0.0-1.0; composition: e,D,T,Ar,W; ip=16MA Bt=6.791T, ; predictive equations: Jpar,Ti,Te,nz; sources: GAUSS [26MW to el / 192MW to D / 192 MW to T]; Transport: BGB+ETB(at 0.97); Impurity: ON; radiation fraction: 50%; current drive: 35%; Zeff: 3.0]