SOURCES AND IMPURITY

IMP3 sources

There is a number of sources developed by IMP3 project, which are actors or internal routines of the transport solver. You can activate them by selecting ON / OFF in front of corresponding source:

• Database Sources – ON - ETS will pick up the evolution of source profiles saved to your input shot/run; OFF-ignored
• Ohmic Heating – ON - ETS will compute Ohmic heating internaly; OFF-ignored
• Gaussian Sources – ON - ETS will add sources from the Gaussian source actor (you can configure heat and particle deposition profiles by editing the code parameters of the actor); OFF-ignored
• Neutral Sources– ON - Fluid neutrals will be solved according to the boundary conditions specified on ¨Before_time_evolution¨ composite actor interface; OFF-ignored
• Switch_IMPURITY– ON - Impurity density and radiative sources will be computed; OFF-ignored; INTERPRETATIVE – profiles of impurity density will be read from input shot/run

IMP5HCD sources

There is a number of sources developed by IMP5 project, that are incorporated by the ETS workflow.

For the IMP5HCD sources please activate the type of heating source, by ticking the box in front of it, and select the code to simulate it.

You also need to configure initial IMP5HCD settings. Therefore please:

• right click on the box ‘BEFORE THE TIME EVOLUTION’
• select ‘Open Actor’
• right click on the box ‘SETTINGS FOR HEATING AND CURRENT DRIVE’
• select ‘Configure actor’
• edit the stettings
• Commit

The detailed information on initial IMP5HCD settings can be found here.

Please note that settings for NBI are done independent for each PINI. Therefore, for NBI settings, please insert the values separated by commas. The number of the element in the array corresponds to the number of activated PINI. Maximum accepted number of PINIs = 16.

Power control

You also can activate the power control for the IMP5HCD sources.

If the POWER_CONTROL is not OFF, there are two modes of operation:specific and frequency

For specific you should specify the time sequence separated by commas and the corresponding power sequence (where first power level corresponds to the first time, second to second and etc.). Linear interpolation will be done between the sequence points.
For example: if you give the power sequence = 2e6,4e6,1e6 and times = 0.0, 0.7, 1.5 (s) the delivered power would be:

For frequency you should specify the power levels sequence separated by commas, start and end time of the power control and the frequency of switching between these levels.
For example: if you give the power sequence = 2e6,4e6,1e6 and frequency = 10 (Hz) tstart =0.0 (s) tend = 1.5 (s) the delivered power would be:

Total power

Profiles of the total source for each channel are obtained from the the individual contributions (Data Base, Gaussian, Neutrals, Impurity and HCD) as a summ of all activated sources multiplied with coefficients specified on the interface of the composite actor.

S_tot = S_DS*DSM + S_GS*GSM + S_Neu*NeuSM + S_IMP*IMPSM + S_HCD*HCDSM

!!! Note, that contributions to all transport equations will be multiplied with the same value.
For example: if ImpuritySourceMultiplier=3.0, then contibutions from impurity to Se, Sz and Qe will be multiplied with 3.0

The fine tuning of of sources can be done through editing the XML code parameters of the source combiner actor:

• right click on the box ‘SOURCES and IMPURITY’
• select ‘Open actor’ to edit settings
• right click on the box ‘Source Combiner’
• select ‘Open actor’ to edit settings
• right click on the box ‘sourcecombiner’
• select ‘Configure actor’
• click ‘Edit Code Parameters’

• If you like the sources to the particular equation being activated - select from_input_CPOs; if you select OFF contributions from all sources to this channel will be nullified.
  For active channels you can adjust multipliers for combining contributions from different source modules (array of five space separated values is expected):

  • first position - Data Base sources;
  • second position – Gaussian sources;
  • third position – HCD sources;
  • fourth position – Neutral sources;
  • fifth position – Impurity sources.

• save and exit
• Commit